Linux version 2.6.30.10 (root@archeo) (gcc version 4.3.3 (GCC) ) #1 Wed Jan 6 15:57:24 CET 2010 prom: fw_arg0=00000007, fw_arg1=a1f77fb0, fw_arg2=a1f78440, fw_arg3=00000008 MyLoader: sysp=00000000, boardp=00000000, parts=00000000 console [early0] enabled CPU revision is: 00019374 (MIPS 24Kc) Atheros AR9132 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00002000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00002000 On node 0 totalpages: 8192 free_area_init_node: node 0, pgdat 802afce0, node_mem_map 81000000 Normal zone: 64 pages used for memmap Normal zone: 0 pages reserved Normal zone: 8128 pages, LIFO batch:0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 board=TL-WR1043ND Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 NR_IRQS:56 PID hash table entries: 128 (order: 7, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29480k/32768k available (1946k kernel code, 3288k reserved, 428k data, 140k init, 0k highmem) SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200) Mount-cache hash table entries: 512 net_namespace: 528 bytes NET: Registered protocol family 16 MIPS: machine is TP-LINK TL-WR1043ND bio: create slab at 0 NET: Registered protocol family 2 Switched to high resolution mode on CPU 0 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. yaffs Jan 6 2010 15:56:21 Installing. msgmni has been set to 57 alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A console handover: boot [early0] -> real [ttyS0] Realtek RTL8366rb switch driver version 0.1.0 rtl8366rb-smi rtl8366rb-smi: using GPIO pins 18 (SDA) and 19 (SCK) rtl8366rb-smi rtl8366rb-smi: RTL5937 ver. 3 chip found rtl8366-smi: probed rtl8366rb init vlan [0]phy_abilityAutoNegotiation : 1 [0]phy_abilityHalf_10 : 1 [0]phy_abilityFull_10 : 1 [0]phy_abilityHalf_100 : 1 [0]phy_abilityFull_100 : 1 [0]phy_abilityFull_1000 : 1 [0]phy_abilityFC : 1 [0]phy_abilityAsyFC : 1 [1]phy_abilityAutoNegotiation : 1 [1]phy_abilityHalf_10 : 1 [1]phy_abilityFull_10 : 1 [1]phy_abilityHalf_100 : 1 [1]phy_abilityFull_100 : 1 [1]phy_abilityFull_1000 : 1 [1]phy_abilityFC : 1 [1]phy_abilityAsyFC : 1 [2]phy_abilityAutoNegotiation : 1 [2]phy_abilityHalf_10 : 1 [2]phy_abilityFull_10 : 1 [2]phy_abilityHalf_100 : 1 [2]phy_abilityFull_100 : 1 [2]phy_abilityFull_1000 : 1 [2]phy_abilityFC : 1 [2]phy_abilityAsyFC : 1 [3]phy_abilityAutoNegotiation : 1 [3]phy_abilityHalf_10 : 1 [3]phy_abilityFull_10 : 1 [3]phy_abilityHalf_100 : 1 [3]phy_abilityFull_100 : 1 [3]phy_abilityFull_1000 : 1 [3]phy_abilityFC : 1 [3]phy_abilityAsyFC : 1 [4]phy_abilityAutoNegotiation : 1 [4]phy_abilityHalf_10 : 1 [4]phy_abilityFull_10 : 1 [4]phy_abilityHalf_100 : 1 [4]phy_abilityFull_100 : 1 [4]phy_abilityFull_1000 : 1 [4]phy_abilityFC : 1 [4]phy_abilityAsyFC : 1 rtl8366s_getEthernetPHY fail for 5!!!! rtl8366s_getEthernetPHY fail for 6!!!! rtl8366s_getEthernetPHY fail for 7!!!! rtl8366s_getEthernetPHY fail for 8!!!! rtl8366s_getEthernetPHY fail for 9!!!! rtl8366s_getEthernetPHY fail for 10!!!! rtl8366s_getEthernetPHY fail for 11!!!! rtl8366s_getEthernetPHY fail for 12!!!! rtl8366s_getEthernetPHY fail for 13!!!! rtl8366s_getEthernetPHY fail for 14!!!! rtl8366s_getEthernetPHY fail for 15!!!! ag71xx_mdio: probed eth0: Atheros AG71xx at 0xb9000000, irq 4 Atheros AR71xx SPI Controller driver version 0.2.4 m25p80 spi0.0: m25p64 (8192 Kbytes) spi0.0: searching for MyLoader partition table at offset 0x10000 spi0.0: searching for MyLoader partition table at offset 0x20000 spi0.0: searching for MyLoader partition table at offset 0x30000 spi0.0: searching for MyLoader partition table at offset 0x40000 spi0.0: no MyLoader partition table found Searching for RedBoot partition table in spi0.0 at offset 0x7e0000 Searching for RedBoot partition table in spi0.0 at offset 0x7f0000 No RedBoot partition table detected in spi0.0 spi0.0: no WRT160NL signature found Creating 5 MTD partitions on "spi0.0": 0x000000000000-0x000000020000 : "u-boot" 0x000000020000-0x000000160000 : "kernel" 0x000000160000-0x0000007f0000 : "rootfs" mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=590000, len=260000 0x000000590000-0x0000007f0000 : "rootfs_data" 0x0000007f0000-0x000000800000 : "art" 0x000000020000-0x0000007f0000 : "firmware" Atheros AR71xx hardware watchdog driver version 0.1.0 ar71xx-wdt: timeout=15 secs (max=21) TCP westwood registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 140k freed Please be patient, while OpenWrt loads ... Registered led device: tl-wr1043nd:green:usb Registered led device: tl-wr1043nd:green:system Registered led device: tl-wr1043nd:green:qss Registered led device: tl-wr1043nd:green:wlan gpio-buttons driver version 0.1.1 input: gpio-buttons as /devices/platform/gpio-buttons/input/input0 Button Hotplug driver version 0.3.1 ar71xx: pll_reg 0xb8050014: 0x1a000000 eth0: link up (1000Mbps/Full duplex) eth0: link down ar71xx: pll_reg 0xb8050014: 0x1a000000 eth0: link up (1000Mbps/Full duplex) eth0: link down mini_fo: using base directory: / mini_fo: using storage directory: /jffs ar71xx: pll_reg 0xb8050014: 0x1a000000 eth0: link up (1000Mbps/Full duplex) device eth0.1 entered promiscuous mode device eth0 entered promiscuous mode br-lan: port 1(eth0.1) entering forwarding state PPP generic driver version 2.4.2 NET: Registered protocol family 24 cfg80211: Using static regulatory domain info cfg80211: Regulatory domain: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) cfg80211: Calling CRDA for country: US SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ath: EEPROM regdomain: 0x0 ath: EEPROM indicates default country code should be used ath: doing EEPROM country->regdmn map search ath: country maps to regdmn code: 0x3a ath: Country alpha2 being used: US ath: Regpair used: 0x3a cfg80211: Regulatory domain changed to country: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) phy0: Selected rate control algorithm 'ath9k_rate_control' phy0: Atheros AR9100 MAC/BB Rev:0 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2 device wlan0 entered promiscuous mode ip_tables: (C) 2000-2006 Netfilter Core Team Driver 'sd' needs updating - please use bus_type methods ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1 ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000 ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usb 1-1: new high speed USB device using ar71xx-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice nf_conntrack version 0.5.0 (512 buckets, 2048 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. xt_time: kernel timezone is -0000 Netfilter messages via NETLINK v0.30. ctnetlink v0.93: registering with nfnetlink. Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning br-lan: port 2(wlan0) entering disabled state device wlan0 left promiscuous mode br-lan: port 2(wlan0) entering disabled state cfg80211: Calling CRDA for country: DE cfg80211: Regulatory domain changed to country: DE (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) (5150000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) device wlan0 entered promiscuous mode device wlan0 left promiscuous mode br-lan: port 2(wlan0) entering disabled state device wlan0 entered promiscuous mode br-lan: port 2(wlan0) entering disabled state br-lan: port 2(wlan0) entering forwarding state scsi 0:0:0:0: Direct-Access SanDisk Cruzer 8.01 PQ: 0 ANSI: 0 CCS scsi 0:0:0:1: CD-ROM SanDisk Cruzer 8.01 PQ: 0 ANSI: 0 usb-storage: device scan complete sd 0:0:0:0: [sda] 15682559 512-byte hardware sectors: (8.02 GB/7.47 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08 sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] Attached SCSI removable disk yaffs: dev is 8388609 name is "sda1" yaffs: passed flags "" yaffs: Attempting MTD mount on 8.1, "sda1" yaffs: dev is 8388609 name is "sda1" yaffs: passed flags "" yaffs: Attempting MTD mount on 8.1, "sda1" br-lan: port 2(wlan0) entering disabled state br-lan: port 2(wlan0) entering forwarding state br-lan: port 2(wlan0) entering disabled state br-lan: port 2(wlan0) entering forwarding state